91
Swap and Sell / Re: 24v minnkota maxxum 70thrust
« Last post by NeedzBaitz on April 04, 2016, 05:00:42 PM »will post sold when sold
Recent Posts
92
Swap and Sell / 2002 TRITON V176 MAGNUM ALUMINUM
« Last post by TAGMAN on April 04, 2016, 03:18:29 PM » Comes with 90hp Yamaha 2 stroke, 80lb thrust minkota, built in charger for tm batteries,
hummingbird gps/depth finder, garmin fish finder up front, batteries 2 years old.
This is a nice sturdy boat that rides good and doesn't tip when you lean over the side.
17'6" long 85" wide. seat needs to be redone and has some carpet ware. boat tops out at 40mph
Asking $6000.00 or best offer.
hummingbird gps/depth finder, garmin fish finder up front, batteries 2 years old.
This is a nice sturdy boat that rides good and doesn't tip when you lean over the side.
17'6" long 85" wide. seat needs to be redone and has some carpet ware. boat tops out at 40mph
Asking $6000.00 or best offer.
93
General Discussion / Re: new boat
« Last post by doogie01801 on April 04, 2016, 01:13:24 PM »Did Joe S. buy a new boat??? https://www.facebook.com/townemarine/photos/a.164726680235232.34661.154404777934089/1059336444107580/?type=3&theater
If so, it is a sweet ride.
If so, it is a sweet ride.
94
Swap and Sell / 2 pflueger presidents for sale
« Last post by NeedzBaitz on April 03, 2016, 06:52:22 PM »70$ for both....
1st reel is 3yrs old
2nd reel is a year old
text jay at 603 401 3867
1st reel is 3yrs old
2nd reel is a year old
text jay at 603 401 3867
95
General Discussion / Mike McNamara Mamorial Open April 24th
« Last post by jman on April 01, 2016, 07:32:17 PM »
96
General Discussion / Re: Interference with my electronics
« Last post by ratherbfishin on March 31, 2016, 07:25:21 PM »Chris,
Don is probably right. His fix is well worth trying.
I was having a similar issue with my Lowrance HDS at the end of the season when running my MK. I'm going to run a thin insulator:
either a piece of rubber or some guys recommend a piece of lead sheathing between the transducer and TM (I don't have a built in transducer)
If Don's fix doesn't work, try going on to bassboat central (link off the NHbasshunters link page) and chances are somebody else
has had a similar issue.
Just curious, how is your sensitivity set on your 788 compared to your 898?
Good luck,
Andy
Don is probably right. His fix is well worth trying.
I was having a similar issue with my Lowrance HDS at the end of the season when running my MK. I'm going to run a thin insulator:
either a piece of rubber or some guys recommend a piece of lead sheathing between the transducer and TM (I don't have a built in transducer)
If Don's fix doesn't work, try going on to bassboat central (link off the NHbasshunters link page) and chances are somebody else
has had a similar issue.
Just curious, how is your sensitivity set on your 788 compared to your 898?
Good luck,
Andy
97
General Discussion / Re: Interference with my electronics
« Last post by Don C on March 31, 2016, 05:56:45 PM »Chris you take a piece of wire 6 feet long
under the front of your boat find the big wire that is the ground for your TM hook the wire to it run the wire along your TM down to the head were the prop is scratch a small spot to bare metal on top of the TM motor head put the bare part of the wire on the part you scratch off put a clamp to hold wire to the bare spot
WHAT YOU ARE DOING IS GROUNDING THE HEAD OF THE TM
under the front of your boat find the big wire that is the ground for your TM hook the wire to it run the wire along your TM down to the head were the prop is scratch a small spot to bare metal on top of the TM motor head put the bare part of the wire on the part you scratch off put a clamp to hold wire to the bare spot
WHAT YOU ARE DOING IS GROUNDING THE HEAD OF THE TM
98
General Discussion / Re: Interferance with my electronics
« Last post by Chris Hoffman on March 31, 2016, 03:09:57 PM »Thanks for the tip Don, I will give that a try, but what are you referring to by taking a piece of wire run it from the ground wire on your MK in the front of your boat ?? HB is sending me a new power cable with a choke that has a ferris built inside to help eliminate RF interference.
99
General Discussion / Re: Interferance with my electronics
« Last post by Don C on March 31, 2016, 02:34:21 PM »Chris before you rip the head apart try take a piece of wire run it from the ground wire on your MK in the front of your boat down to the top of the MK head scratch a spot on top of the head put the wire on the clean spot put a clamp to hold the wire 
I had a lot of big black lines with the ground wire all gone 
I put it under the clamp that holds the transducer 
I had a lot of big black lines with the ground wire all gone I put it under the clamp that holds the transducer 100
General Discussion / Interference with my electronics
« Last post by Chris Hoffman on March 31, 2016, 11:44:04 AM »I was wondering if anyone can give me some pointers on trying to fix / locate the issue of interference. I have a MK Fortrex 101 36v with built in US2 transducer. I have the HB 788ci HD connected to the US2 2d sonar transducer in the Fortrex. When I engage the TM I get severe interference. I have a HB 898 ci SI also located at the bow, but it is connected to a side imaging transducer that is hooked externally to the TM. Both units are connected to the Ethernet hub. While running the TM, I don't experience interference on the HB 898.
I have attempted to trouble shoot by attaching the 788 cables directly to the 898 and I still got interference when engaging the TM. I removed the power cable to the 788 and splice direct to a battery hoping to eliminate the battery connection. I still received interference. Next I thought could it be the Ethernet hubs, removed the 788 from the network and still interference. The only places that I have not checked is the foot control and the head unit. I am told that there is a fuse located underneath the foot control as well as in the head unit of the fortrex.
Any help is greatly appreciated.
I have attempted to trouble shoot by attaching the 788 cables directly to the 898 and I still got interference when engaging the TM. I removed the power cable to the 788 and splice direct to a battery hoping to eliminate the battery connection. I still received interference. Next I thought could it be the Ethernet hubs, removed the 788 from the network and still interference. The only places that I have not checked is the foot control and the head unit. I am told that there is a fuse located underneath the foot control as well as in the head unit of the fortrex.
Any help is greatly appreciated.